Sterile is your friend-to avoid infection and abscesses
To prepare check you have the right vial-not mistaking Tren/Mast/EQ for Test is good[don't laugh-I have]
You will need alcohol pads or paper towel and rubbing alcohol and sterile pkged needle
Do not touch the needle nor allow it to touch anything but cleaned vial and cleaned skin
Wipe the vial with alcohol and the skin where you will inject-that way it dries while you are drawing up liquid
If I injected through wet alcohol-I tended to cough[like a tren cough]the needle carried some alcohol into my system
Dry -no problem even with Tren
Needle length varies-glutes=1-1/2 Quads=1" Delt= 5/8" or 1" if fat=longer needle--if very thin =shorter needle
Open needle pkg -I draw up the Test Cyp/Enanthate with a 22 or 23 gauge needle as the thick oil loads faster and switch it out for a 25 gauge to inject
You just pull the needle and plastic protector off with a counterclockwise twist -then twist new on on--less damage to muscle/less pain
Advantage also that new needle head has not punctured vial rubber which dulls it some.
You can use the 23 gauge with no problems at all to save money.As an Reg.Nurse all patients got intramuscular with 23 gauge.
For the lighter Testosterone's/fast acting Trens/Mast/EQ using a 25 gauge is easy to draw and inject
You draw enough air into syringe to match the amount of drug you want to inject
Push needle through rubber stopper into liquid and push plunger to put air in vial as it needs the back pressure to with draw liquid
Turn vial upside down .making sure liquid is covering needle tip and pull back on plunger till you get the cc quantity you want
Withdraw needle and holding needle end up snap barrel with forefinger to move any air to top of liquid and very gently push up plunger till a drop of liquid comes out--READY
Pop the needle in like a dart from an inch or so from skin-about an inch in unless in Glutes where you go all the way.Now there are 2 schools of thought-one is aspirate which means drawing the plunger out a bit without moving the needle-this is to look for blood in the needle .If none then push plunger in until needle barrel is empty.If a bare bit of blood pull needle back a 1/8 inch and inject or pull right out and move 1/2" reinject with same needle.
Your choice-I almost never aspirate with no problems.
When you slowly withdraw empty needle cover and move around the skin with alcohol pad/paper towel.There may be a feww drops of blood.Don't worry-pressure and moving the skin over hole closes it so you don't lose Test..LOL-most important part.HaHa
Dispose of needle in a sharps container/plasic bottle/pop can so no one sticks themselves and garbage man does not rat you out.
To prepare check you have the right vial-not mistaking Tren/Mast/EQ for Test is good[don't laugh-I have]
You will need alcohol pads or paper towel and rubbing alcohol and sterile pkged needle
Do not touch the needle nor allow it to touch anything but cleaned vial and cleaned skin
Wipe the vial with alcohol and the skin where you will inject-that way it dries while you are drawing up liquid
If I injected through wet alcohol-I tended to cough[like a tren cough]the needle carried some alcohol into my system
Dry -no problem even with Tren
Needle length varies-glutes=1-1/2 Quads=1" Delt= 5/8" or 1" if fat=longer needle--if very thin =shorter needle
Open needle pkg -I draw up the Test Cyp/Enanthate with a 22 or 23 gauge needle as the thick oil loads faster and switch it out for a 25 gauge to inject
You just pull the needle and plastic protector off with a counterclockwise twist -then twist new on on--less damage to muscle/less pain
Advantage also that new needle head has not punctured vial rubber which dulls it some.
You can use the 23 gauge with no problems at all to save money.As an Reg.Nurse all patients got intramuscular with 23 gauge.
For the lighter Testosterone's/fast acting Trens/Mast/EQ using a 25 gauge is easy to draw and inject
You draw enough air into syringe to match the amount of drug you want to inject
Push needle through rubber stopper into liquid and push plunger to put air in vial as it needs the back pressure to with draw liquid
Turn vial upside down .making sure liquid is covering needle tip and pull back on plunger till you get the cc quantity you want
Withdraw needle and holding needle end up snap barrel with forefinger to move any air to top of liquid and very gently push up plunger till a drop of liquid comes out--READY
Pop the needle in like a dart from an inch or so from skin-about an inch in unless in Glutes where you go all the way.Now there are 2 schools of thought-one is aspirate which means drawing the plunger out a bit without moving the needle-this is to look for blood in the needle .If none then push plunger in until needle barrel is empty.If a bare bit of blood pull needle back a 1/8 inch and inject or pull right out and move 1/2" reinject with same needle.
Your choice-I almost never aspirate with no problems.
When you slowly withdraw empty needle cover and move around the skin with alcohol pad/paper towel.There may be a feww drops of blood.Don't worry-pressure and moving the skin over hole closes it so you don't lose Test..LOL-most important part.HaHa
Dispose of needle in a sharps container/plasic bottle/pop can so no one sticks themselves and garbage man does not rat you out.
Last edited:
